• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Pinched yokes?


shortzt

Member
Joined
Jun 25, 2014
Messages
253
Reaction score
1
Points
18
Vehicle Year
1987
Make / Model
Ford
Transmission
Automatic
I just tried to replace my u joint in my drivers side axle on a ttb, but the yokes were bent closer together so I couldn't get the u joint clips on, anybody else have this problem? If so how did you did it
 


alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,931
Reaction score
5,081
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
If your talking c-clips on the outside of the yoke, the only time I've had a problem is when one of the pin bearings [can't think of right term] has fallen over, preventing the cup from bottoming out.
 

shortzt

Member
Joined
Jun 25, 2014
Messages
253
Reaction score
1
Points
18
Vehicle Year
1987
Make / Model
Ford
Transmission
Automatic
Needle bearing and nope I'm talking the ones on the front that the clip goes in the inside, when I press it in the bottom of the slot is showing but not the top, like the yoke is slightly bent like /\ and no matter how much I press them in they don't go in enough
 

alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,931
Reaction score
5,081
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
Needle bearing....thanks.
I still think a needle bearing fallen over is a good possibility. If the needle is taking up space it will still make the joint too wide, regardless if the clips are on the inside or outside. Especially if you removed the old one recently.
 

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
It is very easy to bend the ears of the yoke on those axle shafts. Especially if you are pressing the joints in and out. You will know the ears are bent because when the joint seats the end of the cap will hit you in the face.
 

shortzt

Member
Joined
Jun 25, 2014
Messages
253
Reaction score
1
Points
18
Vehicle Year
1987
Make / Model
Ford
Transmission
Automatic
The ears are bent, I made sure the were no bearings in the bottom, adsm08 are they easy to bend back? Is it safe to put some heat into them
 

Sasquatch_Ryda

Well-Known Member
Ford Technician
OTOTM Winner
Solid Axle Swap
Forum Staff - Retired
TRS Banner 2012-2015
Joined
Aug 8, 2007
Messages
7,916
Reaction score
108
Points
63
Age
36
Location
Terrace, BC, Canada
Vehicle Year
1991
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0L
Transmission
Automatic
2WD / 4WD
Solid Axle Swap 4x4
Tire Size
40s
They bend back easy. Put it in a vise so that it is holding the caps and smack the ears back in place with a hammer till the clips fit.
 

Sponsored Ad


Sponsored Ad

Staff online

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Shran
April Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top