• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

2.3L Intake manifold broken, fixable?


TC260

New Member
Joined
Sep 29, 2010
Messages
4
Reaction score
0
Points
0
Vehicle Year
2001
Make / Model
Ford
Transmission
Manual
I have an '01 Ranger with a 2.3L. To make a long story short, a couple weeks ago it started idling very rough. The code came back as the IMRC valve stuck open. Instead of just replacing the IMRC valve and checking it, the valve cover gasket also needed replacing so I pulled off the intake manifold replaced the gasket, assembled it all back together along with the new IMRC valve.

Now it runs better but still rough. Codes again came back IMRC valve stuck open and too lean in bank 1. Pulled the manifold back off to see if there was a crack or something somewhere and found this end piece that holds the butterfly valve rod broken off as you can see in the pic. Is this something that fixable or is it just replace the whole manifold time?

 


dla

Member
Joined
Sep 24, 2008
Messages
162
Reaction score
0
Points
16
Vehicle Year
2007
Make / Model
Ford
Transmission
Manual
Where's the rubber plug?
 

tchef

New Member
Joined
Oct 28, 2009
Messages
12
Reaction score
0
Points
1
Vehicle Year
2002
Make / Model
Ford
Transmission
Manual
I'm having the same problem and from my searches and testing I found that the manifold wears a hole right behind the power steering pump. Some have fixed it using JB weld but one problem is that it is right were the shaft for the flaps are. Apparently the shaft wears the hole. If you slip a piece of paper in between the power steering pump and the intake right up close to the head you will hear the leak suck the paper up against it and your engine will idle properly.

I have ordered a new manifold for mine. Got it off e-bay for about $200. May be able to do a temp repair by getting something down in there to close the leak in the meantime.
 

tchef

New Member
Joined
Oct 28, 2009
Messages
12
Reaction score
0
Points
1
Vehicle Year
2002
Make / Model
Ford
Transmission
Manual
Photos

Ok here are some photos of the manifold leak problem. Hopefully this can help others. One photo will be of the old manifold with the hole and the other the new one and what it should look like. I bought a new manifold from Fairway Ford off ebay. it was $100 cheaper than at my local dealer. First one they sent was broken in transit and they sent me a new one right away.
 

Attachments

tchef

New Member
Joined
Oct 28, 2009
Messages
12
Reaction score
0
Points
1
Vehicle Year
2002
Make / Model
Ford
Transmission
Manual
Only seems to want to load one file. I'll have to try again later.
 

tchef

New Member
Joined
Oct 28, 2009
Messages
12
Reaction score
0
Points
1
Vehicle Year
2002
Make / Model
Ford
Transmission
Manual
Ok, I got the pictures sized right to load. here they are.
 

Attachments

Scy

New Member
Joined
Nov 7, 2013
Messages
20
Reaction score
0
Points
0
Vehicle Year
2003
Make / Model
Ford
Engine Size
2.3
Transmission
Automatic
Now that you have it off change that darn pcv valve if you haven't already.
 

tchef

New Member
Joined
Oct 28, 2009
Messages
12
Reaction score
0
Points
1
Vehicle Year
2002
Make / Model
Ford
Transmission
Manual
I did that too. What a stupid place to put the PVC valve! And that plastic ring that holds it in!
 

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
While the intake is off is a good time to do the thermostat as well.

I don't believe there is any way to repair a damaged IMRC anymore. There was a kit, years ago, but I got the last one from the obselete warehouse in Hawaii for a customer about 2 years ago.
 

fact150

New Member
Joined
Mar 19, 2014
Messages
6
Reaction score
0
Points
0
Vehicle Year
2003
Make / Model
Ranger
Engine Size
2.3
Transmission
Automatic
I'm doing this tomorrow and I hope it pretty easy . I was already thinking I need to do the pvc valve while I can get to it too . I got the manifold at parts.com which was Sunrise Ford in Cali .
 

gregfirestone

New Member
Joined
Oct 7, 2015
Messages
3
Reaction score
0
Points
1
Transmission
Automatic
Where is the hole at I can't expand the picture to see it is it where the shaft goes straight through the manifold I pulled my apart and it is full of sludge all the way up to number two cylinder had enough room for maybe a 50-cent piece of slide through it the rest was clean but It is a dead miss on number 1 and number 2 it backfires through the exhaust but not the intake getting fuel and spark and the cylinder and plugs are dry when I pull them out after driving it but it's not smoking no oil in the coolant and no coolant in the oil will straighten up and run down the freeway until you hit an incline no matter how slight and then it starts to chug and lose power is this what yours was doing?
 

trex

New Member
Joined
Nov 26, 2019
Messages
6
Reaction score
2
Points
3
Location
nega
Vehicle Year
2008ish
Make / Model
prochallenge ra
Transmission
Manual
hey guys is there a metal intake manifold available for this motor
 

Sponsored Ad


Sponsored Ad

Members online

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Shran
April Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top