• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Can only get 2 converter bolts threaded


Jim Oaks

Just some guy with a website
Administrator
Founder / Site Owner
Supporting Vendor
Article Contributor
TRS Banner 2010-2011
TRS Banner 2012-2015
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Aug 2, 2000
Messages
13,410
Reaction score
8,530
Points
113
Location
Nocona, Texas
Vehicle Year
1996 / 2021
Make / Model
Ford Ranger
Engine Type
4.0 V6
Engine Size
4.0 / 2.3 Ecoboost
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
6-inches
Tire Size
33x12.50x15
Changing out the 4.0 in my 96 Ranger. Got the torque converter lined up, started installing the nuts on the converter, and after tightening 2, I couldn't get the 3rd or 4th nut on. The torque converter bolt doesn't stick through far enough to thread a nut. Also, I can't turn the crank any more. It's like it's jammed up.

I did have to put the bottom (2) bolts in the transmission bellhousing to pull the motor and trans together to get the T/C converter bolts through the flywheel.
 


Will

Forum Staff Member
TRS Forum Moderator
Joined
Nov 30, 2001
Messages
6,925
Reaction score
514
Points
113
Location
Gnaw Bone, Indiana
Vehicle Year
2007
Make / Model
Toyota
Engine Size
4.0
Transmission
Manual
Doesn't seem like the engine and tranny are flush. You can't turn the crank because it's cocked. You should never have to pull anything together. You should never tighten anything before all of the associated fasteners are started. I would start taking it apart. These aren't things you want to force together. When they are lined up, they fit. They are big and heavy in a tight place and hard to line up.
 

alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,870
Reaction score
5,030
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
Hopefully you haven't fubared the pump. Like Will says take it back apart. The tc should click in three times, not two. You could also measure with a straight edge both the block and trans to make sure that the tc is engaged properly.
Good luck,

Richard
 

Grunizzle

01/2013 OTOTM Winner
U.S. Military - Active
V8 Engine Swap
OTOTM Winner
Solid Axle Swap
TRS Banner 2010-2011
TRS 20th Anniversary
Joined
Jan 20, 2009
Messages
1,252
Reaction score
3
Points
38
Location
Albuquerque, NM
Vehicle Year
1991
Make / Model
Ford
Engine Size
4.0L V-6
Transmission
Manual
Does your torque converter have a drain plug that isn't lined up? That could be the issue also
 

Sponsored Ad


Sponsored Ad

Members online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top