• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Safari Pacific MX2 Build


schanusa

November '08 OTOTM Winner
OTOTM Winner
Ham Radio Operator
Joined
Oct 10, 2007
Messages
348
Reaction score
9
Points
18
Age
40
Location
New Mexico
Vehicle Year
2004
Make / Model
Ranger
Engine Type
4.0 V6
Transmission
Manual
2WD / 4WD
4WD
Current Status

Progress on the MX2 ( Before Mods | During Cab Extension | Current )


Action Shots





Original Post
It's about time I started a thread for all my mods....so here it goes.... With the first set of mods already completed, I'm going to jump right into my second phase of modifications. The main goal of the second round is to prepare for a much larger adventure that I'm currently planning. To drive around the world. :smiley_drive:

First things first, removing the old camper shell. It served its function well, but its time to move on. I've crawled through the cab into the camper one to many times and have broken a few interior parts while climbing through. With a few big trips now under my belt I can see new ways to make things much easier as well, especially in gear storage. Attached are two photos. One is the last shot of the camper in use. The second is the rough concept for the new cage to fit on the bed. The new "cage" concept, for lack of better words, will have a low profile and will contain many storage compartments.



To solve my problem of crawling through windows I'm going to toss on an Eezi-Awn tent, but not in an ordinary fashion. The tent will be mounted on sliders level with the truck's bed inside the cage. When I'm ready to camp I can slide out the tent. Once pulled out on the passenger side, the tent will unfold as usual. My idea is to keep the tent lower to the ground while maximizing space above the tent when stashed away.

Storage areas will consist of:
- An upper rack, over the Eezi-Awn,
- Large enclosed box for tools and parts just behind the cab
- Rolling storage boxes under the "cage" accessible from the tailgait

Another idea I'm playing around with is to have a canvas cover made to hide everything inside.

More to come as I plan and start building.... All comments/critiques welcome :)

I started the most difficult part of the modifications this monday. Adding 2 feet onto the rear of the cab and building a small inner cage. I'll post photos as I start to tear into it. The extra 2 feet will contain a future closet and pantry. The exact design is not worked out yet. I'll figure that out once the cab and cage is mostly completed.

Should be fun cutting apart the cab....right? :yikes: I'm a little nervous, so wish me luck...


This is what it should look like when completed........

 
Last edited:


schanusa

November '08 OTOTM Winner
OTOTM Winner
Ham Radio Operator
Joined
Oct 10, 2007
Messages
348
Reaction score
9
Points
18
Age
40
Location
New Mexico
Vehicle Year
2004
Make / Model
Ranger
Engine Type
4.0 V6
Transmission
Manual
2WD / 4WD
4WD
H...e...r...e.... I go... Monday I started chopping up the bed without my body guys. They're a bit busy. Besides, how bad can I mess up.....:D First I pulled the bed of the truck with a forklift. Next came the sticker removal.




Now since I'm adding two feet onto the cab, I will be removing the front portions of the bed for filler material. Easier for keeping the body lines. Leaving 2 inches near the front allows me to keep the original curve around the backside of the bed.




These are the two sections cut from the bed fenders.




Next I drill out all the spot welds holding the boxes' backing and end caps.




Using a dead-blow and chisel I separate the two pieces.

 
Last edited:

schanusa

November '08 OTOTM Winner
OTOTM Winner
Ham Radio Operator
Joined
Oct 10, 2007
Messages
348
Reaction score
9
Points
18
Age
40
Location
New Mexico
Vehicle Year
2004
Make / Model
Ranger
Engine Type
4.0 V6
Transmission
Manual
2WD / 4WD
4WD
Backing removed.



I use a laser level to determine the exact line to cut over the wheel well and other curves in the bed's box. The lines at the bottom were measured at 48 inches.




Double checking myself and making sure the cut would be accurate near the top.




Now I simply trace the laser line, then repeat on the other side.




The bed is cut to size. In the background you can see the portion removed.

 
Last edited:

schanusa

November '08 OTOTM Winner
OTOTM Winner
Ham Radio Operator
Joined
Oct 10, 2007
Messages
348
Reaction score
9
Points
18
Age
40
Location
New Mexico
Vehicle Year
2004
Make / Model
Ranger
Engine Type
4.0 V6
Transmission
Manual
2WD / 4WD
4WD
I clean up the edges and start fitting the backing portion to the bed.





Not too shabby if I do say so myself. I'll start welding and bracing in the next few days.
 
Last edited:

schanusa

November '08 OTOTM Winner
OTOTM Winner
Ham Radio Operator
Joined
Oct 10, 2007
Messages
348
Reaction score
9
Points
18
Age
40
Location
New Mexico
Vehicle Year
2004
Make / Model
Ranger
Engine Type
4.0 V6
Transmission
Manual
2WD / 4WD
4WD
Right, back to work.... After measuring the portions removed to add onto the cab I realize, the wheel well will be 3 inches off. I'll have to scrounge some body parts from a junk yard to complete the cab.

I needed material for welding the backside to the bed, so I used the pieces intended for the cab. I cut two 1 inch strips.



The strips are placed and tack welded inside of the bedsides. This will keep the two exterior pieces closely aligned, resulting in less body filler. Got this tip from my friend.



Strip tacked in place. When I cut the bedsides I didn't cut them completely strait. Around the wheel well there is a small ridge that I wanted to keep. You may see the slight curve near the bottom of the bedside.



After the small strips are tacked in place I start aligning the backside piece.

 
Last edited:

schanusa

November '08 OTOTM Winner
OTOTM Winner
Ham Radio Operator
Joined
Oct 10, 2007
Messages
348
Reaction score
9
Points
18
Age
40
Location
New Mexico
Vehicle Year
2004
Make / Model
Ranger
Engine Type
4.0 V6
Transmission
Manual
2WD / 4WD
4WD
The seems are welded up completely.




Then ground to a semi-smooth finsh.




I refit the bed onto the chassis to start aligning new bolt holes. There will need to be a new brace build along the front as well.








The entire bed has been done by myself and its my first time doing any bodywork... Now I'm feeling confident enough to attempt the cab.... we'll see what happens...hehe :D
 
Last edited:

compleckz

New Member
Joined
Aug 6, 2007
Messages
1,328
Reaction score
3
Points
0
Age
38
Location
Western Mass
Vehicle Year
97
Engine Size
4.0
Transmission
Automatic
awesome! looking forward to following this
 

odie1969

New Member
Firefighter
EMT / Paramedic
Joined
Aug 8, 2007
Messages
1,266
Reaction score
3
Points
0
Location
tempe Az
Vehicle Year
1987
Make / Model
Ford
Engine Size
4.0l sohc
Transmission
Automatic
wow nice job. and if you need any help just send me a p,m I live right down the road, I'm not very skilled but I can learn pretty fast, and play go4. plus I only work 11days a month.
 

Bray D

2012 UA Ranger
OTOTM Winner
Solid Axle Swap
Joined
Aug 8, 2007
Messages
2,144
Reaction score
8
Points
38
Age
37
Location
Manito, IL
Vehicle Year
1996
Make / Model
Ford
Engine Size
4.0
Transmission
Manual
very nice, looking forward to following the progress.
 

OldRedB2_84

New Member
Joined
May 7, 2008
Messages
95
Reaction score
0
Points
0
Age
35
Location
Tulsa, Ok
Vehicle Year
1992
Make / Model
Ford
Engine Size
4.0
Transmission
Manual
looks good, ill be following too! It almost looks like you could put a extended-cab cab on it and modify it to flow with the wheel well lines.
 

dusto2

New Member
Joined
Aug 9, 2007
Messages
667
Reaction score
0
Points
0
Location
scv ca
Vehicle Year
89
Make / Model
ford
Engine Size
2.9
Transmission
Automatic
wow that is goin to be bad ass when done, i have always thought about putting a b2 body on a extended cab frame and graffting bed sides on to it but yours looks like it is going to be sweet
 

Branman

New Member
Joined
Apr 7, 2008
Messages
88
Reaction score
0
Points
0
Age
31
Vehicle Year
89
Make / Model
FORD
Transmission
Automatic

ZMan

Forum Staff Member
TRS Forum Moderator
MTOTM Winner
TRS Event Participant
Joined
Jan 5, 2003
Messages
3,778
Reaction score
406
Points
83
Age
38
Location
Medina, Ohio
Vehicle Year
1992,1994
Make / Model
Ford Rangers
Engine Type
4.0 V6
Transmission
Manual
2WD / 4WD
2WD
Total Drop
4/4, bagged

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top