• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Check engine light flashes while driving?


94DangerRanger

New Member
Joined
Aug 31, 2008
Messages
34
Reaction score
1
Points
0
Location
South Charleston,WV
Vehicle Year
1999
Make / Model
Ford
Engine Size
4.0
Transmission
Manual
Hello all,
I have a 1988 Bronco II with a 2.9 5speed. It runs great only problem the check engine light flashes while I'm driving. When it comes on I can give it gas and it goes right off. WTH? (what the heck) It doesn't affect the performance at all. Any help will be appericated.:icon_confused:
 


B2 Addict

Active Member
V8 Engine Swap
TRS Banner 2012-2015
Joined
Mar 12, 2009
Messages
1,147
Reaction score
9
Points
38
Age
53
Location
Lavergne, TN
Vehicle Year
1984
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
Solid Axle Swap 4x4
Tire Size
37x12.50-17
If I could help I would, but I'm not familiar with all that computer controlled gadgetry. :dunno:

All mine are carb. driven 2.8's & D-sparked so the computers are history :icon_thumby:

Good luck!
 

xlt90

New Member
Joined
Mar 5, 2010
Messages
3
Reaction score
0
Points
0
Location
Quakertown , PA
Vehicle Year
1990
Make / Model
ford
Engine Size
2.9
Transmission
Manual
mine does the same thing i think i'll go to the zone and get the codes read.
 

holeshot

New Member
Joined
Aug 22, 2009
Messages
114
Reaction score
1
Points
0
Vehicle Year
1990
Make / Model
Ford
Engine Size
2.9
Transmission
Automatic
could be something like the O2 sensor shorting out
 

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
No other symptom you say? Probably a bad wire somewhere either causing a minor issue for a few seconds or grounding the light and turning it on.

Is it a consistent flash? If so you may need a new pickup module. I know that on the 96 and up at least a flashing CEL means a class A (dead) misfire and that you need to shut it down before it melts the converter. But if its actually doing that then you'd know about it, unless you are a complete moron, and you don't sound like you are.

The gas thing also kinda makes me think pickup module, since that style sensor isn't wonderful at low speeds, but once you give it gas you speed it up and it starts giving a better signal.
 

brianballard1983

New Member
Joined
Mar 7, 2010
Messages
13
Reaction score
0
Points
0
Vehicle Year
1988
Make / Model
ford
Transmission
Manual
i got a 88 ranger that does the same thing but i got more problems read my thread the tittle is noisy little 2.9. im thinking of unhooking mine
 

bfiakas

New Member
Joined
Jun 2, 2009
Messages
189
Reaction score
1
Points
0
Location
Gilbert AZ
Vehicle Year
1988
Make / Model
Ford
Engine Size
2.9l
Transmission
Manual
I had the same problem, thought it was the MAP sensor becauce the check eng. light came on between 6 to 12 in. of vac. But come to find out it was the TP switch. I bought a used 58mm t-body witch had a bad switch. Put the the switch on from the old t-body and that solved it.
 

Sponsored Ad


Sponsored Ad

Staff online

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Shran
April Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top