• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Towing home a ranger...


rusty ol ranger

Im a Jeep guy now.
Supporting Member
Joined
Sep 22, 2007
Messages
12,267
Reaction score
7,274
Points
113
Location
Michigan
Vehicle Year
1987
Make / Model
Ford
Engine Type
2.9 V6
Engine Size
177 CID
Transmission
Manual
2WD / 4WD
2WD
My credo
A legend to the old man, a hero to the child...
87 ranger 2wd/5sp.

I was planning on using a uhaul dolly behind one of my F250s (prolly the 97).

I read through the sticky thread but couldnt really find a rock hard answer...

Im trying to figure out if a) i should put the back wheels on the dolly and tie the seat belt around the steering wheel b) load the front on the dolly and just tow it home in neutral, or c) load the front tires and yank the driveshaft.

I know pulling the driveshaft isnt hard, but i have a feeling its been on there since 1987 and i dont want to break a bolt or something. I know the owners book says 50 mile max at 35mph with the driveshaft connected, ill be going about 30 miles, but i dont always trust the owners book.

Leaving the steers on the ground makes me a bit nervous, but id figure with my F250 even if something broke and the wheels turned things shouldnt get to wonky as long as i run 45mph or so. But then again i dont really want to screw the column up.

Any input is apperciated.
 


fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,991
Reaction score
2,793
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
If it was me, I'd shoot for option C first, then drop to B if I broke a bolt along the way. For the record, I've had pretty good luck getting driveshaft bolts out with a bit of spray and a decent socket.
 

rusty ol ranger

Im a Jeep guy now.
Supporting Member
Joined
Sep 22, 2007
Messages
12,267
Reaction score
7,274
Points
113
Location
Michigan
Vehicle Year
1987
Make / Model
Ford
Engine Type
2.9 V6
Engine Size
177 CID
Transmission
Manual
2WD / 4WD
2WD
My credo
A legend to the old man, a hero to the child...
If it was me, I'd shoot for option C first, then drop to B if I broke a bolt along the way. For the record, I've had pretty good luck getting driveshaft bolts out with a bit of spray and a decent socket.
1/2 inch right? Its been a while.

Ill bring some PB and map torch, i kinda figured C was best
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,991
Reaction score
2,793
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
Newer ones are 12mm 12 point. I'm not sure about an '87?
 

rusty ol ranger

Im a Jeep guy now.
Supporting Member
Joined
Sep 22, 2007
Messages
12,267
Reaction score
7,274
Points
113
Location
Michigan
Vehicle Year
1987
Make / Model
Ford
Engine Type
2.9 V6
Engine Size
177 CID
Transmission
Manual
2WD / 4WD
2WD
My credo
A legend to the old man, a hero to the child...
Newer ones are 12mm 12 point. I'm not sure about an '87?
Ill just take the big 3 (7/16-1/2-9/16, 12,13,14) i havent been under a ranger in 10 years.
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,991
Reaction score
2,793
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
Make sure they're 12 point and strong.
 

rusty ol ranger

Im a Jeep guy now.
Supporting Member
Joined
Sep 22, 2007
Messages
12,267
Reaction score
7,274
Points
113
Location
Michigan
Vehicle Year
1987
Make / Model
Ford
Engine Type
2.9 V6
Engine Size
177 CID
Transmission
Manual
2WD / 4WD
2WD
My credo
A legend to the old man, a hero to the child...

alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,872
Reaction score
5,031
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
Sooo.... why don't people run the rear wheels up and tie off the steering like old school tow trucks did?
 

rusty ol ranger

Im a Jeep guy now.
Supporting Member
Joined
Sep 22, 2007
Messages
12,267
Reaction score
7,274
Points
113
Location
Michigan
Vehicle Year
1987
Make / Model
Ford
Engine Type
2.9 V6
Engine Size
177 CID
Transmission
Manual
2WD / 4WD
2WD
My credo
A legend to the old man, a hero to the child...
Well all worked out well. The guy rented me his 22ft car trailer with a winch for 40 bucks (which was 20 or 30 cheaper then the uhaul dolly), strapped er down and hauled ass, now the work begins.
 

rangerenthiusiast

New Member
Joined
Aug 26, 2016
Messages
553
Reaction score
2
Points
0
Location
Hudson Valley, NY
Vehicle Year
1992
Make / Model
Ford
Engine Size
4.0
Transmission
Automatic
Well all worked out well. The guy rented me his 22ft car trailer with a winch for 40 bucks (which was 20 or 30 cheaper then the uhaul dolly), strapped er down and hauled ass, now the work begins.
Hey, Rusty. Glad to hear it worked out so well for you! Out of curiosity, why would it be a bad idea to put the fronts up on a car dolly with the driveshafts attached? I know where there’s a parts truck that I was thinking about picking up and just figured that if I did, I’d make sure the rear wheels weren’t locked up, top off the rear diff oil, use a come along to get her up on the dolly (probably a total pain in the @ss), put the shifter in neutral, then gently tow her home. Bad idea?

Thanks and good luck with your project!
 

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
Hey, Rusty. Glad to hear it worked out so well for you! Out of curiosity, why would it be a bad idea to put the fronts up on a car dolly with the driveshafts attached? I know where there’s a parts truck that I was thinking about picking up and just figured that if I did, I’d make sure the rear wheels weren’t locked up, top off the rear diff oil, use a come along to get her up on the dolly (probably a total pain in the @ss), put the shifter in neutral, then gently tow her home. Bad idea?

Thanks and good luck with your project!
It's a lot rougher on an auto than a manual, but basically it's because when you tow with the rear wheels on the ground some part of the trans has to be turning, but the parts that move the lubricating fluids through a transmission are all spun by the engine, and so they aren't moving any lubricating fluids when the engine isn't turning. That will cook a transmission real quick.

It's easier on a 4x4 with a transfer case that can be put in N, because the t-case oil pumps are driven by the output shaft.
 

rusty ol ranger

Im a Jeep guy now.
Supporting Member
Joined
Sep 22, 2007
Messages
12,267
Reaction score
7,274
Points
113
Location
Michigan
Vehicle Year
1987
Make / Model
Ford
Engine Type
2.9 V6
Engine Size
177 CID
Transmission
Manual
2WD / 4WD
2WD
My credo
A legend to the old man, a hero to the child...
It's a lot rougher on an auto than a manual, but basically it's because when you tow with the rear wheels on the ground some part of the trans has to be turning, but the parts that move the lubricating fluids through a transmission are all spun by the engine, and so they aren't moving any lubricating fluids when the engine isn't turning. That will cook a transmission real quick.

It's easier on a 4x4 with a transfer case that can be put in N, because the t-case oil pumps are driven by the output shaft.

Bingo. Its not hard to pull the driveshaft, alot eaiser then changing a transmission.
 

racsan

Well-Known Member
Supporting Member
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 17, 2007
Messages
4,919
Reaction score
4,317
Points
113
Location
central ohio
Vehicle Year
2009
Make / Model
ford/escape
Engine Type
2.5 (4 Cylinder)
Engine Size
2.5/151 I-4
Transmission
Automatic
2WD / 4WD
2WD
Tire Size
235/70/16
My credo
the grey-t escape
i towed one on a 2 wheel dolly once, truck would run so i just let it idle in neutral for the entire trip, was only about 15 miles and i didnt go over 45 with it.
 

rusty ol ranger

Im a Jeep guy now.
Supporting Member
Joined
Sep 22, 2007
Messages
12,267
Reaction score
7,274
Points
113
Location
Michigan
Vehicle Year
1987
Make / Model
Ford
Engine Type
2.9 V6
Engine Size
177 CID
Transmission
Manual
2WD / 4WD
2WD
My credo
A legend to the old man, a hero to the child...
i towed one on a 2 wheel dolly once, truck would run so i just let it idle in neutral for the entire trip, was only about 15 miles and i didnt go over 45 with it.
Unfourtantly, mine wasnt running lol
 

Sponsored Ad


Sponsored Ad

Members online

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Latest posts

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top