• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Spittin' Coolant...


rusty ol ranger

Im a Jeep guy now.
Supporting Member
Joined
Sep 22, 2007
Messages
12,261
Reaction score
7,270
Points
113
Location
Michigan
Vehicle Year
1987
Make / Model
Ford
Engine Type
2.9 V6
Engine Size
177 CID
Transmission
Manual
2WD / 4WD
2WD
My credo
A legend to the old man, a hero to the child...
This issue is driving me insane.

77 F250 400/C6

About the time the t stat pops open, it will blow coolant all over the front of the engine.

But it only does it sometimes, and only till it gets just low enough on coolant it wants to heat up when it idles.

I have replaced the following..
Tstat/gasket
Water pump
Fan clutch
Radiator (3 years old)
Top hose

Its been doing it for a while now. Seems to do it worse in cold weather. I have pressure tested the cooling system, it kept a steady 13lbs (what its rated for), as did the cap.

It dont have a overflow tank, just a vent hose, but after these events its always bone dry.

Any ideas?
 


RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,290
Reaction score
8,290
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
You have the "original" degas system, :)

You don't fill radiator to the top, you leave about 2" of air inside.

As coolant warms up it expands into that 2" gap and pressure goes up to, in your case, 13psi any pressure over that should expel air and maybe some coolant if it was over filled, but that should only happen one time, and as long as you don't add more coolant it shouldn't happen again.

Overflow tank system allows coolant to expand into over flow tank and then it is sucked back in to radiator as engine cools down, so this system wouldn't have/need the air gap in radiator for coolant expansion.

Pressure test should have shown any leaks and blown head gasket or cracked head

But from description it reads like you are either getting a hot spot in a head or have a head gasket issue
If you still have the pressure tester install it and pump it up to 13psi
Then disconnect coil wire on distributor, you want a No Start
Crank engine over while watching the pressure gauge
Pressure should stay steady, no up and down movement
If needle bounces then you have a cylinder leaking into cooling system
You can do same test with a Latex glove, Search for Glove Test

Hot spot in engine is hard to fix, usually a restricted passage.
Hot coolant flashes to steam at the hot spot, this increases pressure in the system above the 13psi and since coolant is already expanded it is at the top of radiator so cap opens and blows out coolant.
Flash to steam also creates "air" vapor which is now in the head so less cooling and engine starts to overheat over all.
 
Last edited:

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,192
Reaction score
17,489
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
Dad's '80 400 would do that once every two years or so. It would freak out whoever was driving it but nothing ever seemed to be wrong with it aside from that. No bubbles in cooling system and no coolant in oil... just coolant all over everything. Not consistent when it did it... just whenever the mood struck it.
 

alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,868
Reaction score
5,029
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
I'll second RonD in that the rad needs to have the fluid down about 1.5-2 inches from the cap.
 

rusty ol ranger

Im a Jeep guy now.
Supporting Member
Joined
Sep 22, 2007
Messages
12,261
Reaction score
7,270
Points
113
Location
Michigan
Vehicle Year
1987
Make / Model
Ford
Engine Type
2.9 V6
Engine Size
177 CID
Transmission
Manual
2WD / 4WD
2WD
My credo
A legend to the old man, a hero to the child...
All good suggestions guys.

85, yeah, thats exactly what mine does, no real rhyme or reason, just, whenever it feels like it.

Ron, ill do that test though, because it does seem to use some coolant. I have a feeling though it might be the intake gasket because i have a helluva time getting any kind of consistant smooth idle. But i know its not spurting from the intake. Oil is not milky.

Hopefully once i get rusty 2.0 rollin i can put the old 77 up for some much needed freshning. I hate driving my 97 and racking up mileage on it.
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top