Home Ford Ranger Forum Tech Articles Other Articles Featured Rangers Readers Rangers Classifieds Shirts & Decals Parts Store

Ford Ranger Discussion Forum  

Go Back   The Ranger Station Forums > Help Forums - Axles, Brakes, Wheels & Tires > Non-Ranger Axles

Non-Ranger Axles All other axles. Ford 9-inch, Dana 44, Dana 60, etc.

Reply
 
Thread Tools Display Modes
Old 11-08-2017, 11:40 AM   #1
evanesce69
Member
 
evanesce69's Avatar
 
Join Date: Jul 2008
Location: Bridge City, Texas
Posts: 254
Vehicle Year: 1993
Vehicle Make: Ford
Vehicle Model: Ranger 4x4 Super Cab
I use this vehicle for: Daily Driver
Rep Power: 19
evanesce69 is on a distinguished road
Send a message via Yahoo to evanesce69
Default 93 Ford Ranger Dana 44 Install

OK, so as the title says, over the weekend I installed full width (non cut and welded) Dana 44 beams into my Ranger.

I intend to document in process in great detail so to share what I have learned so far.

93 Ford Ranger Supercab, 3.0L V6, M5R1, electric BW1354
6" skyjacker suspension lift with extended radius arms
Chevy 64" leaf springs in rear
8.8 out of an '04 SportTrac, Yukon 5.13 R&P, Yukon C clip eliminator kit, Detroit TrueTrac

The front diff is from a 3/4 ton with a Dana 50. It will sport matching 5.13 gears with an Auburn Gear ECTED.
The Dana 50 drop out is a direct bolt in to the D44 beams.

Front ring gear is 9" and rear ring gear is 8.8".


Photos will follow...
__________________
1993 Ford Ranger XL Super Cab 4x4
3.0L FFV Engine from a 2006 Sable @ 250K miles
17x9 Black Rock
P285/70/17 Maxxis Mud Claws

Last edited by evanesce69; 11-08-2017 at 11:52 AM.
evanesce69 is offline   Reply With Quote
Forum Notices (Not shown to 'Premium Members')

 SPRING ONLINE MAGAZINE!

 Check out the latest articles

 Want to become a Premium Member & not see these notices? Click HERE.

Old 11-08-2017, 11:41 AM   #2
evanesce69
Member
 
evanesce69's Avatar
 
Join Date: Jul 2008
Location: Bridge City, Texas
Posts: 254
Vehicle Year: 1993
Vehicle Make: Ford
Vehicle Model: Ranger 4x4 Super Cab
I use this vehicle for: Daily Driver
Rep Power: 19
evanesce69 is on a distinguished road
Send a message via Yahoo to evanesce69
Default

I'll Add descriptions later, but essentially, I had to move the Skyjacker brackets 1.5" forward to allow the wheels to be centered in the wheel wells. This was necessary because at full lock turn the tires were chewing up the lower fender wells just in front of the doors. Since the beams are 3" wider on either side, they were pulled back ever so slightly due to the arc created... While the radius arms did not change length, the position of the beams did....

When the brackets are moved forward, an extension on the transmission crossmember had to be added. Simply a 1.5" move just like the radius arm brackets.

These are FULL length D44 beams, no cut or rotate performed. WMS to WMS is 63". The factory D44 in a 1/2 ton is 65" WMS to WMS. This is because the beam mounts are 2" wider on the Ranger than on the F150's.

The tie rod ends and drag links are '90 F150. An inch needed to be cut off the right side tie rod end and adjoining drag link. The adjuster sleeve needed an inch cut off either side. There is still plenty of room for the clamps to tighten and ample thread engagement. The left side is unmodified.

The knuckles were reamed from the top to accept the tie rod ends. The reamer is a XKUT 1-1/2" TPF BALL JOINT & TIE ROD TAPER REAMER #6952. Easily found on EBay. Be careful to not over ream or the TRE's will not tighten up... Slow and easy with several trial fits.

I used a 6" drop pitman arm for the steering. I think it was a FA600 from Skyjacker. As you can see in the last photo, the steering linkage is nearly parallel. With the D44 beams, you want the axle beam eye bolts to be 1" higher that the spindle centerline. This sets the proper ride height and make alignment much easier. The alignment bushings are MOOG part #'s K80108.

If your smart, you wont lose the F150 sway bar link mounts like I did. I had to cut down the factory D35 mounts.

It is necessary to add a 1/8" shim betweel the radius arm to beam mounts. The D44 beans are 1/8" thinner where the radius arms mount. I used a set of washers that came from the D35 beams. The bolts (both upper and lower) come with these. If you grabbed them from your D44 TTB donor you are in luck.

I do not have a center dropout because it is in the process of being setup. It is a center chunk from a 3/4 ton D50 TTB. The D50 has a 9" ring gear. I am having 5.13's installed on an Auburn Gear ECTED electric locker.

I still have to mock install the drop out to measure for the passenger side inner axleshaft. This is because the beams mounts are 2" wider that the F150's beam mounting points. This narrows the track by 2" and requires shortening the axleshaft by the same 2" on the passenger side. The driver side remains unchanged. Stubshafts, spindles and brakes are all '90 F150.
Attached Images
           

Last edited by evanesce69; Yesterday at 04:06 PM.
evanesce69 is offline   Reply With Quote
Old 11-08-2017, 11:42 AM   #3
evanesce69
Member
 
evanesce69's Avatar
 
Join Date: Jul 2008
Location: Bridge City, Texas
Posts: 254
Vehicle Year: 1993
Vehicle Make: Ford
Vehicle Model: Ranger 4x4 Super Cab
I use this vehicle for: Daily Driver
Rep Power: 19
evanesce69 is on a distinguished road
Send a message via Yahoo to evanesce69
Default

reserved 2
__________________
1993 Ford Ranger XL Super Cab 4x4
3.0L FFV Engine from a 2006 Sable @ 250K miles
17x9 Black Rock
P285/70/17 Maxxis Mud Claws
evanesce69 is offline   Reply With Quote
Old 11-08-2017, 11:43 AM   #4
evanesce69
Member
 
evanesce69's Avatar
 
Join Date: Jul 2008
Location: Bridge City, Texas
Posts: 254
Vehicle Year: 1993
Vehicle Make: Ford
Vehicle Model: Ranger 4x4 Super Cab
I use this vehicle for: Daily Driver
Rep Power: 19
evanesce69 is on a distinguished road
Send a message via Yahoo to evanesce69
Default

reserved 3
__________________
1993 Ford Ranger XL Super Cab 4x4
3.0L FFV Engine from a 2006 Sable @ 250K miles
17x9 Black Rock
P285/70/17 Maxxis Mud Claws
evanesce69 is offline   Reply With Quote
Old 11-08-2017, 11:43 AM   #5
evanesce69
Member
 
evanesce69's Avatar
 
Join Date: Jul 2008
Location: Bridge City, Texas
Posts: 254
Vehicle Year: 1993
Vehicle Make: Ford
Vehicle Model: Ranger 4x4 Super Cab
I use this vehicle for: Daily Driver
Rep Power: 19
evanesce69 is on a distinguished road
Send a message via Yahoo to evanesce69
Default

reserved 4
__________________
1993 Ford Ranger XL Super Cab 4x4
3.0L FFV Engine from a 2006 Sable @ 250K miles
17x9 Black Rock
P285/70/17 Maxxis Mud Claws
evanesce69 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Ford Ranger: Module Install Jetchip JET Performance Products 0 10-28-2015 01:44 PM
DIY: Ford Ranger Double DIN Install TheTwanksta Stereo & Video 19 01-14-2015 01:46 PM
2007 Ford ranger air bag install help 07LoanRanger 3.0 Liter Forum 3 01-23-2013 01:00 PM
98 Ford Ranger Custom Install win1 Stereo & Video 4 05-24-2008 01:14 PM
98 Ford Ranger Custom Install win1 Stereo & Video 3 05-19-2008 06:21 PM




All times are GMT -5. The time now is 06:51 PM.




1999-2014 / 959 Media LLC / All Rights Reserved