• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Spring eye bushing replacement


fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,987
Reaction score
2,789
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
I'm sprinting to get the swap complete on the Ranger this week and trying to offload a couple of smaller tasks. Have any of you guys paid a shop to replace spring eye bushings? I've got a set of sport trac leaves I'd like to throw in while the bed is off but would love to skip the labor time of installing new bushings. Just curious what a shop might charge.
 


Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.
Probably going to pay an hours labor so anywhere from 75-100 bucks.

However I say do it youself, if you buy poly bushings they dont need to be pressed in so zero time to install. And I've always just burned the old rubber bushings out. 20 minutes with even a little propane torch is all it takes. Just hit them with the torch till the rubber catches fire and then let them burn. After a few minutes you can just poke them out with a screwdriver. clean they eyes with some scotchbrite then the new poly bushings just slide in. Simple job.
 
Last edited:

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,987
Reaction score
2,789
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
Tempting. If I can get my hands on a set of poly bushings quickly I might just do that. I burned out one of the rubber bushings on my existing springs today, then promptly blew up my largest c clamp trying to press in the new one.
 

Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.
Look up the part number you need at energy suspenions website then just buy them on amazon. Youll prolly have them by Tuesday lol.
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,987
Reaction score
2,789
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
I've been trying to do just that. So far I've come up empty on any urethane options for an 02 Sport Trac.
 

Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.
I've been trying to do just that. So far I've come up empty on any urethane options for an 02 Sport Trac.
Can you measure the I.D of the spring eye, width of the spring, and overall width of the oem bushing? Alot of times you dont buy them per specific vehicle but buy size alone.
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,987
Reaction score
2,789
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
I can do that tomorrow and try to dig through a catalog. Thanks for the suggestion.
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,987
Reaction score
2,789
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
For anybody who cares...

There's nothing in the ES catalog that directly fits the 2nd gen Explorer and 1st gen Explorer Sport Trac front leaf spring eye (RB237). Per some users over at Explorer Forum, you can use Energy Suspension part number 3.2125 for that purpose if you leave the original metal sleeve in place.

The rear spring eye is the same size as the Ranger's, so RB131 or equivalent will work there.
 

alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,868
Reaction score
5,029
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
Which catalogue did you use? I need to find a bushing for a non spec application.
edit; ES = Energy Suspension
Online or paper?
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,987
Reaction score
2,789
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,987
Reaction score
2,789
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
For anybody who cares...

There's nothing in the ES catalog that directly fits the 2nd gen Explorer and 1st gen Explorer Sport Trac front leaf spring eye (RB237). Per some users over at Explorer Forum, you can use Energy Suspension part number 3.2125 for that purpose if you leave the original metal sleeve in place.

The rear spring eye is the same size as the Ranger's, so RB131 or equivalent will work there.
Energy suspension 3.2125 was perfect for the explorer front eye bushings. I burned out the rubber core, ground out the remaining rubber with a rotary rasp bit, then tapped the urethane pieces right in.
https://m.harborfreight.com/high-carbon-steel-rotary-rasp-set-10-pc-62694.html

Quick question on the rear eye bushings. Should I take these sleeves out?

This is what's going in. Slightly different than the stock bushing. https://www.truckspring.com/products/Rubber-Leaf-Spring-Bushing-Type-1__RB-131.aspx
 

Attachments

Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.
The link doesn't work but its fine to leave the sleeve in place if the replacement bushings require it for proper fit. Just make sure you file down the burrs.
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,987
Reaction score
2,789
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
I hit with a sanding wheel so no burrs, but it definitely doesn't appear to fit. I can't lay my hands on my calipers at the moment or I'd confirm inside and outside diameter.

Which link doesn't work?
 

Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.
The link to the bushings isnt coming up for me. Poly bushings should never be press fit or fall right in. Some grease and hand pressure should be all it takes...
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,987
Reaction score
2,789
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top