• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

2nd Gen 4.0 intakes and harness


Denisefwd93

Denisefwd93

Well-Known Member
Joined
May 20, 2015
Messages
2,261
Reaction score
74
Points
48
Location
South East PA
Vehicle Year
1994
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Total Lift
stock, may get leveling springs in front "somday"
Tire Size
235
1994 4.0 , seeking bad engine but all good wiring harness intake brackets etc...
SE PA area Don't really want the block but will take it to get the goods.
 
Last edited:


adsm08

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
PM gpmiller. I know he has a 2000ish truck that will have a good bit of what you want with a blown 4.0.
 
Denisefwd93

Denisefwd93

Well-Known Member
Joined
May 20, 2015
Messages
2,261
Reaction score
74
Points
48
Location
South East PA
Vehicle Year
1994
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Total Lift
stock, may get leveling springs in front "somday"
Tire Size
235
adsm08 said:
PM gpmiller. I know he has a 2000ish truck that will have a good bit of what you want with a blown 4.0.
Click to expand...
Oh. Wouldn't that be too new?
I'm thinking, set up the 98 with intake, brackets, electrical, virtually everything that's on the same generation engine in my 94 truck.

I know a friend and me, WILL NOT be putting in engine is this truck. (1994) "someday".

I am " thinking" that a completely set up and ready to drop in engine will save time and cost of whoever I pay to do the job. But that is what I do, think too much LOL
 
adsm08

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
The accessory brackets should all be the same. I don't know about the intake. I know for the Rangers it changed from metal to plastic around 93, but I don't know the exact years. I think he is using the harness, but it wouldn't work for you anyway.
 
Denisefwd93

Denisefwd93

Well-Known Member
Joined
May 20, 2015
Messages
2,261
Reaction score
74
Points
48
Location
South East PA
Vehicle Year
1994
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Total Lift
stock, may get leveling springs in front "somday"
Tire Size
235
adsm08 said:
The accessory brackets should all be the same. I don't know about the intake. I know for the Rangers it changed from metal to plastic around 93, but I don't know the exact years. I think he is using the harness, but it wouldn't work for you anyway.
Click to expand...
Not a priority at this time, I'm thinking the lower intake is identical, just the upper intake is plastic, which is/was cast aluminum.
 
BlackBII

BlackBII

Ranger Custom
Article Contributor
OTOTM Winner
TRS Banner 2010-2011
Truck of Month
Joined
Aug 14, 2007
Messages
7,895
Reaction score
982
Points
113
Location
UT
Vehicle Year
1989
Make / Model
Ford
Engine Type
4.0 V6
Transmission
Manual
2WD / 4WD
4WD
Total Lift
5
Tire Size
33
I believe '95 was the first year of the plastic upper plenum. The plastic and aluminum ones can be swapped, but I have't seen a plastic one with the intake air temp bung, so you'd have to drill a hole for that.

The lower intakes are the same.
 
adsm08

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
BlackBII said:
I believe '95 was the first year of the plastic upper plenum. The plastic and aluminum ones can be swapped, but I have't seen a plastic one with the intake air temp bung, so you'd have to drill a hole for that.

The lower intakes are the same.
Click to expand...
You might be right about 95 being the change over year.

I know when I was looking I was after an aluminum EGR intake, and so Rangers were mostly ruled out, and I was looking exclusively at Explorers.
 
Last edited:
bergz0

bergz0

Member
Joined
Nov 13, 2007
Messages
451
Reaction score
8
Points
18
Age
34
Location
nj
Vehicle Year
1993
Make / Model
ford
Engine Type
4.0 V6
Transmission
Manual
2WD / 4WD
4WD
Total Lift
leveling kit
Tire Size
31x10.50x15
im going to be pulling the engine in my 93' ranger soon with the 4.0, i might have what you need
 
Denisefwd93

Denisefwd93

Well-Known Member
Joined
May 20, 2015
Messages
2,261
Reaction score
74
Points
48
Location
South East PA
Vehicle Year
1994
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Total Lift
stock, may get leveling springs in front "somday"
Tire Size
235
bergz0 said:
im going to be pulling the engine in my 93' ranger soon with the 4.0, i might have what you need
Click to expand...
Where you at, local to me? what I'm looking to do is get this low mileage engine we have in storage set up for the day when we ultimately have it dropped into the truck I just picked up.
 
bergz0

bergz0

Member
Joined
Nov 13, 2007
Messages
451
Reaction score
8
Points
18
Age
34
Location
nj
Vehicle Year
1993
Make / Model
ford
Engine Type
4.0 V6
Transmission
Manual
2WD / 4WD
4WD
Total Lift
leveling kit
Tire Size
31x10.50x15
im in washington nj 07882
 

AdirondackRanger

New Member
Supporting Member
Joined
May 22, 2016
Messages
46
Reaction score
0
Points
0
Location
Adirondack park
Vehicle Year
88
Make / Model
ford
Engine Size
2.9
Transmission
Automatic
My credo
I brake for leaves that could be frogs
Denisefwd93 said:
1994 4.0 , seeking bad engine but all good wiring harness intake brackets etc...
SE PA area Don't really want the block but will take it to get the goods.
Click to expand...
would be worth a trip to the pick and pull. I use Gary's U Pull it. Colesville Rd Binghamton, NY. They're off I81 just north of the PA border in NY.

This is in no means a shameless plug for them... There's a lot of good older vehicles there.. and price is good. They even have yard guys that will pull the harder things cheap for cash.
 
Denisefwd93

Denisefwd93

Well-Known Member
Joined
May 20, 2015
Messages
2,261
Reaction score
74
Points
48
Location
South East PA
Vehicle Year
1994
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Total Lift
stock, may get leveling springs in front "somday"
Tire Size
235
I don't know if it's a local thing or just BS but all the yards in my area U-Pull-It, and regular yards the first thing they say is "too old nothing over 10 years!"
 
You must log in or register to reply here.

Sponsored Ad


Sponsored Ad

Staff online

Members online

Total: 646 (members: 12, guests: 634)

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Latest posts

Truck of The Month


Shran
April Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

Latest Album Photos

Hunters
20240409_190831.jpg
20240409_190818.jpg
20240409_180824.jpg
20240409_182648.jpg
20240409_181010.jpg
20240408_175026.jpg
99 Ranger
20200706_161414.jpg
20240207_155117.jpg
20240207_155111.jpg
20240207_154537 - Copy.jpg

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top