Search results


  1. Broncojumper87

    b2 alignment specs

    So getting new wheels and tires put on the b2 today as well as getting it aligned. When doing the alignment do you go off of the factory specs for caster and camber? I found a picture of the specs on this site with a little searching but the shop is saying that since the ride height changed from...
  2. Broncojumper87

    87 b2 2.9 tick

    So what do you know my engine in my b2 starting ticking recently. When it first happened I changed the oil went with 10w-40 and added some stp engine treatment which helped. That lasted tell now about 3000 miles or so now it will tick after driving on the highway or long drives but it comes and...
  3. Broncojumper87

    33s with a 4 inch llift

    I looked through the tech section and seen the tire chart. My question is where exactly do you run into issues with the 33s? I have 31s now and it looks like there is a ton of room in there? Its time for new wheels and tires and i came across a set of 15x10 beadlocks for 200 and from the...
  4. Broncojumper87

    B2 towing question

    Okay so i kind of have this redneck idea for a cheap camper that im curious if my b2 would be able to pull it. My idea is to find a ranger that has been cut in half and the bed and rear section turned into a trailer. I want to find a slide in camper or a bigger shell preferably the slide in...
  5. Broncojumper87

    weird idle issue

    So I bought an ecm with a jet chip from a fellow member after I installed it in my 87 b2 it started idling at 2000. (before it idled around 1000) after tinkering around with it a bit I just put the old computer back in and it still does it. Now it will idle normal sometimes for a little bit then...
  6. Broncojumper87

    I broke my hydraulic clutch line in my 87 b2

    Long story short I broke the hydraulic clutch line right at the fitting that goes into the slave cylinder. searched the net wasn't able to find a new replacement. This is my dd so I need to figure something out quick. I was hoping maybe someone had one laying around or had one on a parts truck...
  7. Broncojumper87

    2.9 to 4.0 clutch swap

    Who has done one? Besides clutch flywheel and starter anything else I need. any particular year to buy parts for aside from just pre 97?
  8. Broncojumper87

    drive shaft help

    So I have an 87 b2 4x4 with a 5 speed the original cv style drive shaft crapped its self today. question is what drive shaft will be long enough for a rough country 4 inch lift.
  9. Broncojumper87

    off road light what size fuse and relay

    Picked up some kc highlights for free from a buddy anyway not sure how big of a fuse and relay to use
  10. Broncojumper87

    No instrument cluster lights

    I replaced my head light switch because it wouldn't turn on my dome light. Now when I turn on my dome light it pops the fuse for my instrument cluster. I took the switch back and exchanged it for another to Se if maybe it was faulty but still does the same thing. Any ideas what would cause this?
  11. Broncojumper87

    electric fan install

    Came across an electric fan laying in the garage slapped in on the bronco now I'm lost as to where to pull power from so my question is how do you guys do it?
  12. Broncojumper87

    explorer leaf spring bushing replacement

    Long story short picked up a set of explorer leafs on the cheap and thought it would be a good idea to swap out the bushings before installing them. My question is what bushings should I use and how hard are they to change.
  13. Broncojumper87

    Radius arm extensions

    Was reading through some build threads came across some stone crusher extensions.i haven't been able to find them but I'm curious as to how hard it would be to make some?
  14. Broncojumper87

    Who is using the 2 piece extended Brake line

    Just wondering who is using the 2 piece brake line from the tech section? How reliable is it and what are your thoughts on it?
  15. Broncojumper87

    Ruff stuff 4 inch lift

    Just finished installing my 4 inch lift and the way I understood it was that with drop brackets you wouldn't need camber bushings. from the way it looks though I'm going to. Am I wrong about this or could there be another issue? Everything on the front end is new bushings and balljoints. I do...
  16. Broncojumper87

    Upgrade to super runner steering or no

    I have an 87 b2 that I just installed a 4 inch lift on it anyway all the front end parts need replaced ball joints tierods ect. Should I even bother with Oem replacements or hold off on the super runner steering tell I upgrade to a d35.
  17. Broncojumper87

    Axle pivot bushing install

    I'm installing energy suspension axle pivot bushings in my 87 b2 and I'm lost as to where the big o-ring type bushing goes? The oem bushing didn't have anything that looks like that.
  18. Broncojumper87

    A few questions about explorer leaf springs

    First question what year explorer should I look for? I would assume that as long as its not the independent rear or the mono leaf it's all the same but just want to make sure before I go to the local yard. Next question how lift can I get from combining some of the bronco pack with the explorer...
  19. Broncojumper87

    Extending rear brake line and diff breather?

    I kind of have an idea on the breather thinking about extending it up next to the filler neck not sure if that's the best place for it but it seams to be the highest place to mount it within reason. The rear brake line on the other hand I'm not real sure about I did go through the tech library...
  20. Broncojumper87

    Do you lose abs when switching to a locker

    Picked up a locker on the cheap for my b2 just curious if I will be able to keep my abs


Top